Service Hotlineshaft retaining ring installation tool and an installation method thereof relate to an assembly tool and an installation method thereof, comprising a pressing cylinder and a taper sleeve. The maximum diameter of the tapered end is slightly smaller than the inner diameter of the circular straight hole of the pressing cylinder, and the lower end of the tapered sleeve has a positioning structure matched with the shaft of the shaft retaining ring to be installed. The method includes the following: place the taper sleeve on one end of the shaft where the shaft retaining ring is to be installed and position it well, then place the shaft retaining ring on the tapered end of the taper sleeve, and finally press down the pressure cylinder to make the shaft Use the retaining ring to slide down the conical surface of the taper sleeve to the shaft to be installed with the retaining ring for the shaft, and finally get stuck in the groove of the shaft. Yueluo does not need to open the retaining ring for the shaft, which reduces the operation force and labor intensity. The operation method is simple, the structure is simple and reliable, the cost is low, and it is easy to popularize and use.
The DISC-LOCK lock nut is composed of two parts, each part has staggered cams. Due to the internal wedge design, the slope angle is greater than the nut angle of the bolt, the combination will be tightly bite into a whole, when vibration occurs. When the DISC-LOCK lock nut is staggered, the raised parts of the DISC-LOCK lock nut move with each other to generate lifting tension, so as to achieve a perfect anti-loosening effect.
With the rapid development of China's machinery industry, especially the development of heavy industry, the demand for large-scale metal processing equipment is increasing; at the same time, higher requirements are also placed on the technical parameters of the equipment. For some large-scale CNC equipment, to ensure the machining accuracy of the whole product, it is not only necessary to rely on high-performance components such as full closed-loop control and precision transmission components, but also requires the positioning and stability of the joint surfaces between the large and medium-sized components of the equipment. The common positioning of the joint surface between large components adopts flat key positioning, and this method requires processing the keyway at the joint surface of the large components. Since the joint surface of large parts is affected by factors such as processing and splicing, it cannot guarantee that the keyways on the large parts combined can be matched according to the theoretical requirements. Therefore, the positioning flat key needs to press the flat key in the two parts of large parts. Different repair allowances Trim into a stepped shape. The height difference of this keyway in different large components makes a single flat key need to be repaired on four sides, which increases the difficulty of the key repair process and makes it difficult to improve work efficiency. Not only that, when the flat key is repaired and assembled, it must be in an interference fit with the keyway, which makes the disassembly and assembly of the flat key more laborious.
Classification broadcast product series Product detailed classification Hexagon bolts (1) Hexagon bolts (1) Hexagon full teeth: GB5783/DIN933 (2) Hexagon half teeth; GB5782/DIN931 (3) Class B flange hexagon bolts: GB5787 (4) Joint bolts: GB798/DIN444 (5) Welding bolts for manual welding: GB902 square neck bolts (1) Half round head square neck bolts: GB14/DIN603 (2) Small half round head square neck bolts: GB12 (3) Half round head low square neck bolts: GB801 Remarks: Square neck bolts and carriage bolts Hexagon socket head cap screws (1) Hexagon socket head cap screws: GB70/DIN912 (2) Hexagon socket flat end set screws: BG70/DIN913 (3) Hexagon socket head set screws: GB78/DIN914 ( 4) Countersunk head socket head socket head set screw: GB79/DIN915 (5) Hexagon socket socket head set screw: GB80/DIN916 (6) Hexagon socket head countersunk head screw: DIN7991 (7) Hexagon socket head thin head screw: DIN7984 ( 8) Plug screw: ISO7379 machine screw (1) Slotted cylinder head screw: GB65/DIN84 (2) Slotted pan head screw: GB67/DIN85 (3) Slotted countersunk head screw: GB68/DIN963 (4) Slotted Large flat head screw (5) Cross recessed small pan head screw: GB823 (6) Cross recessed large flat head screw (7) Cross recessed pan head screw: GB818/DIN7985 (8) Cross recessed countersunk head screw: GB819/DIN965 (9 ) Cross recessed countersunk head screw: GB820/DIN966 thread and stud (2) Stud bolt-bm=1d: GB897/DIN938 (3) Stud bolt-bm=1.25d: GB898/DIN939 (4) Stud head Bolt-bm=1.5d: GB899 (5) Stud bolt-bm=2d: GB900 (1) Tooth bar: GB15389/DIN976 (6) Equal length stud: GB901/DIN976
Materials and main equipment: 1.1 Bolts, nuts and washers shall be accompanied by quality certificates and shall comply with design requirements and national standards. 1.2 The high-strength bolts should be stored in categories according to their specifications, and should be protected from rain and moisture. Do not use if the bolts and nuts are not matched and the threads are damaged. If the bolts, nuts and washers are corroded, the tightening axial force should be sampled and used only after meeting the requirements. Bolts, etc. shall not be contaminated by soil or oil, and shall be kept clean and dry. It must be used in the same batch according to the batch number, and must not be mixed or mixed. 1.3 Main tools: electric torque wrench and controller, manual torque wrench, manual wrench, wire brush, tool bag, etc. 2 Operating conditions: 2.1 Friction surface treatment: The friction surface is treated by sandblasting, grinding wheel grinding and other methods, and the friction coefficient should meet the design requirements (a requirement is that the Q235 steel is above 0.45, and the 16 manganese steel is above 0.55). The friction surface wood is allowed to have residual iron oxide scale. The treated friction surface can generate red rust surface and then install the bolts (generally stored in the open air for about 10d). The sandblasted friction surface can be installed without rusting. When grinding with a grinding wheel, the grinding range is not less than 4 times the diameter of the bolt, the grinding direction is perpendicular to the direction of force, and the friction surface after grinding should be free of obvious unevenness. The friction surface should be prevented from being polluted by oil or paint. If polluted, it should be cleaned thoroughly. 2.2 Check the hole size of the bolt hole, the burrs on the edge of the hole must be removed. 2.3 The bolts, nuts and washers of the same batch number and specification should be packaged for use. 2.4 Electric wrenches and manual wrenches should be calibrated.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: slip-joint screws, 912 micro-miniature screws, switch socket screws, brass outer screws and other products, we can provide you with fastening suitable for you piece solution.
