Service Hotline1. For low strength (below 500 N/mm2 or below 60000 psi) bolts use general soft steel, generally use SAE 1008 or JIS SWRM 8 (or SWRCH 8). 2. Lower strength (600 N/mm2 or 74000 psi) ) bolts use general soft steel, but limited carbon content grade, generally use SAE 1010 - 1015 or JIS SWRM 10 - 15 (or SWRCH 10 - 15). .3. Higher strength ( 800 N/mm2 or 125000 psi ) bolts of medium carbon steel, low carbon boron steel plus quenching and tempering, generally use SAE 1035 - 1040 or SWRCH 35K - 40K. 4. High strength (900 N/mm2 or more or 150000 psi or more) bolts use medium carbon Alloy steel or low carbon boron steel, in terms of application, if the metric Class 10.9 uses low carbon boron steel, the imprint should be added under the series imprint to become 10.9, and the imprint of the inch 8.2 grade is also used with the general Grade 8 bolts The imprint is different for easy identification. High-strength bolts made of low carbon boron steel cannot be used in high temperature conditions. The design strength exceeds Class 12.9 or ASTM A574 ultra-high strength bolts are limited to medium carbon alloy steel plus quenching and tempering. The performance grades of bolts for steel structure connection are divided into more than 10 grades such as 3.6, 4.6, 4.8, 5.6, 6.8, 8.8, 9.8, 10.9, 12.9, etc. Among them, the bolts of grade 8.8 and above are made of low-carbon alloy steel or medium-carbon steel and are heat-treated (quenching, tempering), commonly known as high-strength bolts, the rest are commonly known as ordinary bolts. The bolt performance grade label consists of two parts of numbers, which represent the nominal tensile strength value and yield ratio of the bolt material respectively. For example, a bolt with a performance level of 4.6 means: 1. The nominal tensile strength of the bolt material is 400MPa; 2. The yield ratio of the bolt material is 0.6; 3. The nominal yield strength of the bolt material is 400×0.6=240Mpa . Performance level 10.9 high-strength bolts, after heat treatment, can achieve: 1. The nominal tensile strength of the bolt material is 1000MPa; 2. The yield ratio of the bolt material is 0.9; High-strength bolts, processing and manufacturing problems are compared Small, general fastener manufacturing companies can master the manufacturing process; but problems are prone to occur in material selection and heat treatment. Material selection is the primary link. Various alloying elements have a great influence on the properties of the material, and the material must be subjected to spectral composition analysis; secondly, the fracture problem and the choice of heat treatment process have a great influence and are very important. Dealers and traders must control the inspection and performance testing links; automotive fasteners have high requirements and must carefully control the quality.
In the prior art, the spring washer has a certain anti-loosening effect. However, due to the unreasonable design structure, the upper and lower pressing forces of the spring washer and the spring washer's anti-return force are poorly matched, resulting in the smooth surface and the bolt head. The friction between the nut and the connected parts is small. When the bolt or nut is subjected to strong vibration, the bolt or nut will still loosen. Therefore, the anti-loosening effect of the above spring washer still needs to be improved.
In order to overcome the above problems, Guangdong Yueluo Hardware Industry Co., Ltd. provides a screw that can be quickly installed and removed. Using the principle of lever, press the handle downward, and the screw can form a backward force through the connecting piece. Press the screw and nut tightly; lift the handle, the screw forms a forward force, and the screw can be removed. Thus, the time and manpower for screwing during installation and disassembly are reduced. The solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. to solve its technical problems is that the entire screw includes a screw rod, a nut, a connecting piece, a circlip, a positioning pin, a small shaft, a fixed piece, a base, and a handle; the screw is connected by the small shaft at the upper end. At the upper end of the connecting piece, the handle is connected to the lower end of the connecting piece, and the front end of the handle is connected to the base fixing piece through a positioning pin. There are gaps at both ends of the small shaft, and the small shaft is installed through the circlip. The front end of the handle can only be rotated on the positioning pin. Due to the lever principle, when the handle is pressed down, it will drive the screw at the front end of the connecting piece, so that the screw generates a backward force and tightens the screw and the nut. On the contrary, when the handle is pulled up, the screw generates a forward force, so that the screw can be easily removed. The beneficial effect of Guangdong Yueluo Hardware Industry Co., Ltd. is that the quick-opening screw saves the time and labor of repeatedly twisting the nut during installation and disassembly. The installation and removal process is simple.
The screw is usually installed in the threaded hole of the part, and its main function is to fix the relative position between the two parts. It is widely used in various industries. A traditional screw generally includes a screw rod and a head located at one end of the screw rod. During installation, the screw rod is connected with a threaded hole, and the head is located outside the screw hole and abuts on the edge of the screw hole.
screw is a tool that uses the physical and mathematical principles of the circular rotation and friction of an object to fasten the parts of the object step by step. Since the parts to be fixed are different, different types of screws are required for different applications. Press screw is a new type of fastener applied to thin plate or sheet metal. The principle is to press the embossed teeth into the preset holes of the sheet metal. The diameter of the general preset holes is slightly smaller than the outer diameter of the pressure riveting screw. The periphery of the hole is plastically deformed, and the deformed object is squeezed into the guide groove, thereby producing a locking effect. However, the existing pressing screws are easy to loosen due to long use time or frequent vibrations, which is prone to certain hidden dangers.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: multi-wave spring washers, countersunk head machine screws, sealed waterproof nuts, DIN6927 hexagonal flange lock nuts and other products, we can provide You have the right fastener solution for you.
