your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Production knurled cylindrical head hand screw cross hand twist adjustment screw 3/8 5/8

author:[email protected] Click:7739end source: time:2023-10-27 03:30:36

Summary of information:We have more than ten years of production experience in the screw industry. The main products are: high-strength Dacrome...

The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the deficiencies in the existing technology and provide a square nut fastener for cable tray installation, which has a simple and reasonable structure, and is extremely convenient and flexible to operate; it does not occupy C-shaped steel after installation. The space at the bottom increases the diversity of installation, and can be applied to square nuts of different thicknesses, and the installation is firm

safety screw includes a screw rod, and is characterized in that: the two ends of the screw rod are respectively provided with notches for rotating a tool knife. Compared with the prior art, the advantage of Guangdong Yueluo Hardware Industry Co., Ltd. is that notches are provided at both ends of the screw, so that when the screw is in use, it can be tightened or loosened from both ends without installation. Due to the limitation of position and structure, when the installation space is small or the tool knife cannot be inserted, it is convenient for the operator to directly tighten or loosen the screw from the other end, which improves the efficiency of installation and disassembly, saves assembly time and reduces assembly difficulty.

Cross recessed pan head screws refer to cross recessed machine wire screws, which are represented by the letters PM. The country stipulates that the thread specification is M1.6-M10, the performance level is 4.8, A-50, A2-70, CU2, CU3 and AL4, H-type and Z-type cross recessed, and the product grade is Class A cross recessed pan head screws . If other technical requirements are needed, they should be selected from the current standards (such as GB/T196, GB/T3106, GB/T3098.1, GB/T3098.6 and GB/T3098.10).

total of 13 domestic automotive fastener companies were interviewed and investigated in this survey, and all the companies under investigation have passed the TS16949 system certification. An average car has about 1500 fasteners, and the total bolt assembly time for each car is about 2.5~3.2h. It can be seen that the variety and quality of fasteners have an important impact on the level of the main engine and the quality of the vehicle. This article analyzes the localization of high-strength threaded fasteners and the management of supply quality from the perspective of the production process of high-strength threaded fasteners. Product flow of high-strength threaded fasteners The production process of high-strength threaded fasteners is raw material transformation → cold heading forming → thread processing (thread rolling or thread rolling) → heat treatment → surface treatment → sorting and packaging, generally used above grade 10.9 Thread rolling process after heat treatment. The steel grades commonly used for high-strength bolts of automotive fastener materials are 35 steel, 45 steel, and ML35 steel for grade 8.8 bolts; 35CrMo for grade 10.9 bolts; 40Cr; 35CrMo, 42CrMo, and SCM435 for grade 12.9 bolts. The raw materials for domestic fasteners are basically in the hot-rolled state, while the steel for fasteners produced in Japan and other countries is basically in the state of direct cold heading. Users do not need pretreatment, which can reduce costs from the link. Common failure modes of fastener failure are assembly elongation, fatigue fracture, and delayed fracture. In addition to the material, the quality of cold heading forming and thread processing (thread rolling or thread rolling, tapping) threaded fasteners, forming equipment and thread processing equipment and molds (production process and equipment) are the key factors to ensure their quality. Especially in the state of large-scale and multi-variety supply, automotive fasteners that require high machining accuracy, how to ensure product consistency and defect prevention is one of the problems faced by fastener production. For the cold heading equipment and thread processing equipment of the investigated companies, domestic equipment accounts for about 40%, Taiwan equipment accounts for 50%, and imported (Europe, America, Japan) equipment accounts for about 10%; Partial folding, thread streamline upsetting, tooth wrinkles and cracks, etc. Domestic fastener factories are limited by capital or other reasons, and most of them use domestic equipment and Taiwan equipment to produce fasteners for automobiles. To ensure the dimensional tolerance and geometric tolerance of large-scale production of high-end fastener products, online monitoring should be increased. Means and mold making level. Eliminate unqualified products in production, so as to ensure the assembly quality of OEMs and OEMs. [1] About 80% of the surveyed fastener enterprises have heat treatment equipment, and most of them use Taiwan heat treatment process lines; the process line equipment is a continuous mesh belt furnace with atmosphere protection, and the atmosphere, temperature and process parameters are controlled by a computer. The high-strength fastener industry is a relatively competitive industry. If we want to have a thorough and objective analysis of the technology and market of the high-strength fastener industry, we need to start from the following aspects: domestic high-strength fasteners Industry and Enterprise Competition Pattern High-strength Fastener Industry Industrial Policy High-strength Fastener Product Technical Standards and Regulations my country's High-strength Fastener Product Technology Competition Pattern Dynamics Regarding these six aspects, many domestic research institutions have conducted in-depth research and research, and many institutions have long been engaged in research and research in this industry.

At present, there are two methods for removing rivets in the market, one is non-destructive manual removal, which has low work efficiency and high work intensity. The other is mechanical destructive dismantling, such as the electric drill dismantling method. This method has high work efficiency, but it is easy to cause damage to the riveted product, and it is easy to cause the rivet to splash, and the operation is dangerous.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: double-pass knurled round copper posts, 12.9 half-tooth screws, non-knurled cylindrical head screws, spring washers and other products, we can provide you with The right fastener solution for you.

hand screw

Production of knurled cylindrical heads


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].