Service HotlineThe flat gasket product is an accessory on the high-speed rail backing plate. The product requires two planes to be flat, the shape and size of the inner hole are accurate, and there are no casting defects (such as air holes, shrinkage holes, sand holes, etc.), and the casting material requires GB/T450-10 . Due to the light weight and large demand of flat gaskets, if they are produced by ordinary sand casting process, the castings are prone to deformation, sand holes, air holes and other casting defects, and the molding area is large, the production efficiency is low, and the production tasks are difficult to complete.
Currently, a screw generally includes a shank body, a threaded portion formed on the outer edge of the shank body, and a conical head formed at the rear end of the shank body. When the current thread is in use, since the thread part is cylindrical, the thread part and the workpiece are vertical, so it is relatively laborious when in use, and it is difficult to locate, lock and unlock.
Generally known bolts refer to screws with a larger diameter. According to this statement, the diameter of screws is much smaller than that of bolts. Stud bolts do not have a head, and some are called studs. Both ends of the stud are threaded, with no thread in the middle and a smooth rod in the middle. Studs are used on large equipment such as gear racks. In actual use, the external load will have vibration and the influence of temperature will reduce the frictional force, and the threaded connection will loosen and fail over time. Therefore, it is necessary to do a good job in the maintenance of the stud bolts at ordinary times. Stud bolts or anchor bolts will have problems under the action of mechanical friction for a long time. When problems occur, the engine oil pan should be removed, and the use of the engine bearing bushes should be carefully checked, and the clearance between the bearing bushes should be checked. Whether it is too large, if the gap is too large, it should be replaced in time. When replacing the stud bolts, also replace the connecting rod bolts. When some large equipment such as nail making machines are in normal operation, if they find that the engine is not running very stable or there is abnormal noise, they should stop and check in time to avoid bigger problems.
In the riveting connection of various structural parts, waterproof lantern rivets have been widely used in riveting environments that require waterproofing. After the riveting parts are riveted, the waterproof structure area of the mandrel and the waterproof structure of the rivet body There is no complete close fit between the areas. In some riveting ranges, the waterproof performance of the rivet is affected. The main reason is that the traditional processing technology of the mandrel and the materials used bring many troubles to the riveting process. is a problem to be solved at present.
National Standard 1 GB/T3103.3-2000 Fastener Tolerance Flat Washers 2 GB/T5286-2001 General Scheme of Flat Washers for Bolts, Screws and Nuts 3 GB/T9074.1-2002 Bolts or Screws and Flat Washers Assemblies 4 GB/ T9074.18-2002 Self-tapping screws and flat washers assembly 5 GB/T 95-2002 Flat washers C grade 6 GB/T96.1-2002 Large washers A grade 7 GB/T96.2-2002 Large washers C grade 8 GB/ T97.1-2002 Flat washer Class A 9 GB/T97.2-2002 Flat washer chamfered Class A 10 GB/T97.4-2002 Flat washer for screw and washer assemblies 11 GB/T97.5-2002 Flat Washers for self-tapping screws and washer assemblies 12 GB/T848-2002 Small washers Class A 13 GB/T5287-2002 Extra large washers Class C 14 GB/T4678.13-2003 Die-casting mold parts Part 13: Push plate washers 15 GB /T4605-2003 Rolling bearing thrust needle roller and cage assemblies and thrust washers 16 GB/T97.3-2000 Flat washers for pins 17 GB/T18230.5-2000 Flat washers for bolted structures quenched and tempered 18 GB/T9074 .5-2004 Cross recessed small pan head screw and flat washer assembly 19 GB/T9074.20-2004 Cross recessed hexagon head self-tapping screw and flat washer assembly 20 GB/T3762-1983 Sharp angle seal for tube fittings Washers 21 GB/T1231-2006 High-strength large hexagon head bolts, large hexagon nuts, and washers for steel structures Specifications 22 GB/T1230-2006 High-strength washers for steel structures 23 GB/T2861.10-2008 Die guides - Part 10 : Washers 24 GB/T5649-2008 Lock nuts and washers for pipe joints 25 GB/T94.3-2008 Technical conditions for elastic washers Saddle, wave elastic washers 26 GB/T3099.1-2008 Terms of fasteners threaded fasteners , pins and washers 27 GB/T10447-2008 Elements and tolerances of semicircular thrust washers for sliding bearings 28 GB/T94.1-2008 Technical conditions for elastic washers Spring washers 29 GB/T10446-2008 Dimensions and tolerances for full circle thrust washers for sliding bearings 30 GB/T93-1987 standard spring washer 31 GB/T94.2-1987 elastic washer technical conditions toothed, serrated lock washer 32 GB/T98-1988 stop washer technical conditions 33 GB/T849-1988 spherical washer 34 GB/ T850-1988 Cone Washer 35 GB/T851-1988 Split Washer 36 GB/ T852-1988 Square bevel washer for I-beam 37 GB/T853-1988 Square bevel washer for channel steel 38 GB/T854-1988 Single ear stop washer 39 GB/T7244-1987 Heavy spring washer 40 GB/T855-1988 Double lug Stop washers 41 GB/T7245-1987 Saddle spring washers 42 GB/T7246-1987 Wave spring washers 43 GB/T856-1988 Outer tongue stop washers 44 GB/T858-1988 Stop washers for round nuts 45 GB/T859- 1987 Light spring washer 46 GB/T860-1987 Saddle elastic washer 47 GB/T861.1-1987 Internal tooth lock washer 48 GB/T861.2-1987 Internal serrated lock washer 49 GB/T862.1-1987 External tooth Lock Washers 50 GB/T862.2-1987 External Serrated Lock Washers 51 GB/T955-1987 Wave Elastic Washers 52 GB/T27938-2011 Sliding Bearing Thrust Washers Failure Damage Terms, Appearance Features and Reasons 53 GB/T956.1 -1987 Conical Lock Washer 54 GB/T956.2-1987 Conical Serrated Lock Washer 55 GB/T28697-2012 Rolling Bearing Self-aligning Thrust Ball Bearing and Self-aligning Seat Washer Dimensions 56 GB/T9074.2-1988 Cross Groove Pan head screw and external serrated lock washer assembly 57 GB/T9074.3-1988 Cross recessed pan head screw and spring washer assembly 58 GB/T9074.4-1988 Cross recessed pan head screw, spring washer and flat washer assembly 59 GB/T9074.7-1988 Cross recessed small pan head screw and spring washer assembly 60 GB/T9074.8-1988 Cross recessed small pan head screw and spring washer and flat washer assembly 61 GB/T9074.9-1988 Cross recessed Countersunk head screw and conical lock washer assembly 62 GB/T9074.10-1988 Cross recessed half countersunk head screw and conical lock washer assembly 63 GB/T9074.11-1988 Cross recessed pocket hexagon head bolt and flat washer Assembly 64 GB/T9074.12-1988 Cross-recessed hexagon head bolt and spring washer assembly 65 GB/T9074.13-1988 Cross-recessed hexagon head bolt, spring washer and flat washer assembly 66 GB/T9074.15 -1988 Hexagon head bolt and spring washer assembly 67 GB/T9074.16-1988 Hexagon head bolt and serrated lock washer assembly 68 GB/T9074.17-1988 Hexagon head bolt, spring washer and flat washer assembly 69 GB/ T9074.26-1988 Spring washers for assemblies Ring 70 GB/T9074.27-1988 External Serrated Lock Washers for Assemblies 71 GB/T9074.28-1988 Conical Lock Washers for Assemblies 72 GB/T1030-1988 Inner Spherical Washers
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: plastic hand-tight nuts, backrest pin rubber rings, blue race steel washers, GB878 slotted external thread cylindrical pins and other products, we can help you Provide the right fastener solution for you.
