Service HotlineNational Standard 1 GB/T3103.3-2000 Fastener Tolerance Flat Washers 2 GB/T5286-2001 General Scheme of Flat Washers for Bolts, Screws and Nuts 3 GB/T9074.1-2002 Bolts or Screws and Flat Washers Assemblies 4 GB/ T9074.18-2002 Self-tapping screws and flat washers assembly 5 GB/T 95-2002 Flat washers C grade 6 GB/T96.1-2002 Large washers A grade 7 GB/T96.2-2002 Large washers C grade 8 GB/ T97.1-2002 Flat washer Class A 9 GB/T97.2-2002 Flat washer chamfered Class A 10 GB/T97.4-2002 Flat washer for screw and washer assemblies 11 GB/T97.5-2002 Flat Washers for self-tapping screws and washer assemblies 12 GB/T848-2002 Small washers Class A 13 GB/T5287-2002 Extra large washers Class C 14 GB/T4678.13-2003 Die-casting mold parts Part 13: Push plate washers 15 GB /T4605-2003 Rolling bearing thrust needle roller and cage assemblies and thrust washers 16 GB/T97.3-2000 Flat washers for pins 17 GB/T18230.5-2000 Flat washers for bolted structures quenched and tempered 18 GB/T9074 .5-2004 Cross recessed small pan head screw and flat washer assembly 19 GB/T9074.20-2004 Cross recessed hexagon head self-tapping screw and flat washer assembly 20 GB/T3762-1983 Sharp angle seal for tube fittings Washers 21 GB/T1231-2006 High-strength large hexagon head bolts, large hexagon nuts, and washers for steel structures Specifications 22 GB/T1230-2006 High-strength washers for steel structures 23 GB/T2861.10-2008 Die guides - Part 10 : Washers 24 GB/T5649-2008 Lock nuts and washers for pipe joints 25 GB/T94.3-2008 Technical conditions for elastic washers Saddle, wave elastic washers 26 GB/T3099.1-2008 Terms of fasteners threaded fasteners , pins and washers 27 GB/T10447-2008 Elements and tolerances of semicircular thrust washers for sliding bearings 28 GB/T94.1-2008 Technical conditions for elastic washers Spring washers 29 GB/T10446-2008 Dimensions and tolerances for full circle thrust washers for sliding bearings 30 GB/T93-1987 standard spring washer 31 GB/T94.2-1987 elastic washer technical conditions toothed, serrated lock washer 32 GB/T98-1988 stop washer technical conditions 33 GB/T849-1988 spherical washer 34 GB/ T850-1988 Cone Washer 35 GB/T851-1988 Split Washer 36 GB/ T852-1988 Square bevel washer for I-beam 37 GB/T853-1988 Square bevel washer for channel steel 38 GB/T854-1988 Single ear stop washer 39 GB/T7244-1987 Heavy spring washer 40 GB/T855-1988 Double lug Stop washers 41 GB/T7245-1987 Saddle spring washers 42 GB/T7246-1987 Wave spring washers 43 GB/T856-1988 Outer tongue stop washers 44 GB/T858-1988 Stop washers for round nuts 45 GB/T859- 1987 Light spring washer 46 GB/T860-1987 Saddle elastic washer 47 GB/T861.1-1987 Internal tooth lock washer 48 GB/T861.2-1987 Internal serrated lock washer 49 GB/T862.1-1987 External tooth Lock Washers 50 GB/T862.2-1987 External Serrated Lock Washers 51 GB/T955-1987 Wave Elastic Washers 52 GB/T27938-2011 Sliding Bearing Thrust Washers Failure Damage Terms, Appearance Features and Reasons 53 GB/T956.1 -1987 Conical Lock Washer 54 GB/T956.2-1987 Conical Serrated Lock Washer 55 GB/T28697-2012 Rolling Bearing Self-aligning Thrust Ball Bearing and Self-aligning Seat Washer Dimensions 56 GB/T9074.2-1988 Cross Groove Pan head screw and external serrated lock washer assembly 57 GB/T9074.3-1988 Cross recessed pan head screw and spring washer assembly 58 GB/T9074.4-1988 Cross recessed pan head screw, spring washer and flat washer assembly 59 GB/T9074.7-1988 Cross recessed small pan head screw and spring washer assembly 60 GB/T9074.8-1988 Cross recessed small pan head screw and spring washer and flat washer assembly 61 GB/T9074.9-1988 Cross recessed Countersunk head screw and conical lock washer assembly 62 GB/T9074.10-1988 Cross recessed half countersunk head screw and conical lock washer assembly 63 GB/T9074.11-1988 Cross recessed pocket hexagon head bolt and flat washer Assembly 64 GB/T9074.12-1988 Cross-recessed hexagon head bolt and spring washer assembly 65 GB/T9074.13-1988 Cross-recessed hexagon head bolt, spring washer and flat washer assembly 66 GB/T9074.15 -1988 Hexagon head bolt and spring washer assembly 67 GB/T9074.16-1988 Hexagon head bolt and serrated lock washer assembly 68 GB/T9074.17-1988 Hexagon head bolt, spring washer and flat washer assembly 69 GB/ T9074.26-1988 Spring washers for assemblies Ring 70 GB/T9074.27-1988 External Serrated Lock Washers for Assemblies 71 GB/T9074.28-1988 Conical Lock Washers for Assemblies 72 GB/T1030-1988 Inner Spherical Washers
Yueluo relates to a self-tapping screw according to the preamble of claim 1. A self-tapping screw is known from EP0623759B1, the ratio of the outer diameter to the smaller diameter of the self-tapping screw is about 1.25-1.5, the ratio of the outer diameter to the pitch lead is about 1.5-1.6 and the thread The flank angles of , are < 50° and ≥ 35°. EP0433484B1 proposes a self-tapping screw whose thread is provided with cutting teeth of approximately arcuate design, and the cutting edge and the thread crest are at the same horizontal position and are set in opposite directions. One purpose of Yueluo is to realize a general type of self-tapping screw so that it can be screwed particularly easily into holes drilled in concrete or other materials such as bricks and the like. According to Yueluo, this object is achieved by the features in the characterizing part of claim 1, and surprisingly, it has been found that the parallel arrangement of the flanks, ie with a flank angle of about 0°, will make screwing particularly easy when screwing in , especially if the diameter of the hole varies within an allowable tolerance. One reason may be due to the fact that there is no lateral pressure on the material screwed into the thread, even if threads of different depths are cut in concrete or other materials such as brick, chipped plywood, or hardwood. The thread cuts into the material over its entire width by cutting grooves. In particular according to the embodiment of claim 4 the material cut out when screwing in the screw can be discharged without any accumulation, the dependent claims reflecting many advantages of further embodiments.
In the process of completing the adjustment of the position of the object, the nut will move up and down with the entry and exit of the screw, and it cannot make a sound for people to perceive, and it cannot provide people with a position change distance through the action of rotation.
Figure 1 is a schematic structural diagram of Guangdong Yueluo Hardware Industry Co., Ltd. Figure 2 is a front view of the structure of the riveted positioning block. FIG. 3 is a top view of the structure of the riveted positioning block. Figure 4 is a front view of the structure of the riveting lower die. Figure 5 is a side view of the structure of the riveting lower die. 1, I is a rivet, 2 is a riveting positioning block, 3 is a product, 4 is another product, and 5 is a riveting lower die. [0017] Referring to Figure 2, Figure 3, 2-1 is a positioning pin, 2-2 is a rivet hole, and 2-3 is a through hole. Referring to Figure 4, Figure 5, 5-1 is a positioning hole, 5-2 is a guide block, 5_3 is a countersunk screw hole, and 5_4 is a vacant hole.
In order to achieve the above purpose, Yueluo provides the following technical solutions: threaded rivets include a nail rod, an expansion piece, and a nail sleeve, one end of the nail rod is provided with a mounting piece, and the side of the mounting piece away from the nail rod is movably installed with a mounting piece. There is a driving mechanism. The driving mechanism includes a mounting cylinder and a movable rod. A cross groove is formed at one end of the mounting piece close to the driving mechanism. The rod is movably installed on the inner side of the installation cylinder, and one end of the movable rod close to the cross groove is fixedly provided with a cross connecting piece that matches the cross groove, the cross connecting piece is matched with the cross groove, and the movable rod is far away from the cross groove. One end of the cross connecting piece is fixedly provided with a fixing piece, the fixing piece and the installation cylinder are screwed together by threads, the expansion piece is sleeved on the outer side of the nail rod, and the nail sleeve is movably installed on the nail rod away from the driving mechanism The outer side of one end of the nail rod is movably installed with a fixing mechanism.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: internal and external teeth without intervening furniture connector screws and nuts, all-tooth socket head screws, B-type hexagon thin nuts, DIN7991 bolts and other products, we can provide you with products such as Provide the right fastener solution for you.
